• Comparative analysis of design/build and design/bid/build project delivery systems in Lebanon

• A Supplier Strategy to Control the Bullwhip Effect

• Prediction of deflection in reinforced concrete beams containing plastic waste

• Flexural characteristics of reinforced concrete beams containing lightweight aggregate in the tensile zone

• Characterization of Thermal Treated Clay Obtained from Lebanese Local Resources as Supplementary Cementitious Materials

• Characterization of Fly Ash Originated From Lebanese Municipal Solid Waste Plant

• Selected Properties of Concrete Containing Palm Fibres

• Effect of Partial Replacement of Cement by MSWI-BA on the Properties of Mortar

• Properties of Concrete made of Fine Aggregates Partially replaced by Incinerated Municipal Solid Waste Bottom Ash

• Processing of incinerated municipal solid waste fly ash for use in concrete

• Repair of Damaged Prestressed Concrete Beams Using CFRP Fabric and Stitching Techniques

• Manufacturing of Lightweight Aggregates from Municipal Solid Waste Incineration Bottom Ash and their Impacts on Concrete Properties

• Evaluation of Kaolin Clay Collected From Lebanese Sources in Cementitious Systems

• Numerical Modeling of Rigid Steel Beam-Column Connections Subjected to Cyclic Loads

• Effect of Successive Impact Loads from a drop Weight on a Reinforced Concrete Flat Slab

• Numerical Punching Shear Analysis of Unbonded Post-Tensioned Slabs with Inverted-U Shaped

• Repair of Pre-stressed Concrete Beams using Coupler and Presetessed Strands

• Effect of palm fibers addition on absorption characteristics and mechanical properties of concrete

• Selected Properties of Concrete Containing Municipal Solid Waste Incineration Bottom Ash (MSWI-BA)

• The Impact of Steel Fibers on the Properties of Self Compacting Concrete

• Effect of Wet-Mat Curing Time on Chloride Permeability of Concrete Bridge Decks

• A Health Monitoring Framework for Optimal Service Life Predictions of Steel Structures Under Fatigue Loading

• An Ensemble Kalman Filter Approach for Estimating Site Specific Earthquake Response

• Probabilistic identification of the effects of corrosion propagation on reinforced concrete structures via deflection and crack width measurements

• New continuous strain-based description of concrete's damage-permeability coupling

• Damping in Transient Pressurized Flows

• Effect of Soil - Structure Interaction Constitutive Models on Dynamic Response of Multi-Story Buildings

• The Effect of Underground Stories on the Dynamic Response of High-Rise Buildings

• Seismic assessment and rehabilitation of a historical masonry mosque

• Geotechnical and Numerical analysis of Bcharreh Landslide stability

• Engineering Student Retention and Graduation with Improvement Strategies: The Case of Beirut Arab University

• Advanced Characterization of Asphalt Concrete Mixtures Reinforced with Synthetic Fibers

• Development of Probabilistic Viscoelastic Continuum Damage Model for Asphalt Concrete

• Characterisation of the mechanical performance of asphalt concrete mixtures with selected WMA additives

• On the Enhancement of Surface Plasmon Resonance Biosensors by Graphene for Medical Applications

• Overview of Fiber Optic Surface Plasmon Resonance Biosensors for Medical Applications

• On the Design of Graphene Surface Plasmon Resonance Sensors for Medical Applications

• Miniaturized branch-line coupler based on slow-wave microstrip lines

• Towards automatic setup of non-intrusive appliance load monitoring – feature extraction and clustering

• Design of a low cogging torque Axial Flux Multilayer Permanent Magnet Synchronous Machine for wind turbines applications

• Performance of Time-Reversal for Indoor Communications

• Design Procedure of Two-Dimensional Circularly Polarized Slotted Waveguide Antenna Arrays

• Implantable Antennas for Biomedical Applications: An Overview on Alternative Antenna Design Methods and Challenges

• Differential AGC with Offset Stability and Wide Range Frequency Synthesis

• Axes-Based Encryption key

• Scrambled Prime Key Encryption

• Advanced Biomimetic Cells Architecture for Parallel Operations in Artificial Intelligence

• A Novel Implementation of Ternary Decoder Using CMOS DPL Binary Gates

• Smart Grid and Photovoltaic System to Mitigate Blackouts and Load Shedding

• Tunable Bandpass Filter Using Series Connected Varactor Diodes

• Universal Filtered Multi-Carrier Peak to Average Power Ratio Reduction

• Controlled Brushless De-Excitation Structure for Synchronous Generators

• Performance Improvement of Brushless Generator Voltage Regulation by Using a Controlled Non Linear Discharge Resistor

• Comparative Study on the Energy Consumption of Underfloor Heating System Utilizing Different PCM

• Performance of the one-ended evacuated tubes as medium temperature solar air heaters at low flow rates

• Modeling the interply slip during forming of thermoplastic laminates

• Recycling of Waste Mixed Plastics Blends (PE/PP)

• GPS tracking system for autonomous vehicles

• A New Method for Limb Singularity Analysis of Parallel Manipulators

• An experimental study on using diethyl ether in a diesel engine operated with diesel-biodiesel fuel blend

• Modelling of contaminant dispersion in underfloor air distribution systems: comparison of analytical and CFD methods

• Comparative CFD Investigation of Upper Room UVGI Efficacy with Three Different Ventilation Systems

• Artificial neural network predication and validation of optimum suspension parameters of a passive suspension system

• Caractérisations mécaniques des charnières pour meuble

• Experimental analysis of the influence of the impinged plate by an impinging jet on the vortex dynamics using PIV

• Experimental investigation of the correlation between the dynamics of an impinging jet on a slotted plate and the acoustic field generated

• Tomographic and Time-Resolved PIV measurement of an Impinging Jet on a Slotted Plate

• Volumetric Proper Orthogonal Decomposition of an impinging jet using SPIV measurement

• Analysis of the effect of the 3C kinematic field of a confined impinging jet on a slotted plate by stereoscopic PIV